Strainer Pour With a Twist: the Monsoon Blossom

Creating the ‘Monsoon Blossom’ with a twist, takes the strainer technique one step further. Some of the most beautiful paintings have been created by pouring over a strainer, colander or similar item. When mentioned to those outside the pouring community it may seem like we have lost our minds. It’s a beautiful kind of crazy. The amazing patterns that form as you slowly and methodically add color are the only thing needed to convert even the most cynical observer. Personally, I love that part!

Supplies I Used:

• • Artist Loft Titanium White and Mars Black 1:4 paint : Floetrol
  • Liquitex Basics Unbleached Titanium 1:4 paint : Floetrol
  • Craftsmart Spanish Tile and Aquamarine Metallic 1:2 paint : Floetrol
  • FolkArt Multi-Surface Fire Opal Metallic 1:2 paint : Floetrol
  • Essential Value Treadmill Belt Lubricant
  • Floetrol Flood
  • Artist Loft Black Canvas wrapped frame 12×16
  • Can Colander
  • Cups: Plastic cups to mix paints, three ounce Dixie cups to measure, you can use clear plastic or silicone cups to mix and measure if you have them.
    ○

Tip

• • : Never mix your paints in cups that are coated in wax, you may end up with

wax chips in your painting

• .
• Stir sticks

Preparing the Canvas

“Monsoon Blossom” starts with a black canvas covered in a thin layer of black paint. This was my first time using a black canvas, so I wanted to play it safe by only using a black liquid base—next time I will be braver. I picked these up at Michaels, a two pack of 12×16 Artist Loft Black Canvas for $10.99. I used what was officially called a can colander, but I just can’t seem to call something the size of a soup can, a colander, so it will be referred to as a strainer.

Starting the Pour

I placed the strainer right side up on the wet canvas—I had it in the middle, but that’s up to you. Next, add half an ounce to one ounce of Titanium White to the middle of the strainer. There should be just enough to cover the bottom of the strainer, that will then start to slide through the side openings. Paint to Floetrol ratios are listed in the supplies.

No Pour Cup Needed

Instead, pour each color (individually) into the strainer. After adding the first layer of white, I poured the remaining paints in the following order (I did not repeat the sequence):

• One ounce of Fire Opal
• Drizzle of Mars Black
• Half an ounce of Unbleached Titanium
• Half an ounce of Spanish Tile
• Drizzle of Mars Black
• Half an ounce of Titanium White
• Half an ounce of Aquamarine Metalic (with four drops of silicone)
• One inch puddle of Titanium White
• Drizzle Mars Black
• Half an ounce of Fire Opal

Silicone is used in the Aquamarine only, as you will have cells form with the Titanium White and Unbleached Titanium. Then the drizzling and use of varied weighted paints aides in the lacing throughout the piece.

Take a Moment

Let the pour sit and continue to ease out the sides of the strainer, creating the patterns, cells, and lacing. Wait until no more paint is coming through the sides. Don’t worry if there is still some paint in the bottom of the strainer.

The Twist

Now for the twist—make sure the strainer stays on the canvas while you turn it one full twist of the wrist, basically 180 degrees. Next, slowly lift straight up and place your hand under the strainer to catch any drips while removing from the canvas.

Tip: Place the strainer in water immediately for easier cleaning later.

Tilting

Start tilting, being careful not to over stretch your cells or (if you want them) the petal forms.

Tip: tilt in a circular motion if you want to keep it more centered on the canvas.

I wanted some black negative space, but if you don’t, you can add more paint in your initial pours, increasing each by just a small amount, it won’t take much. This will change your final painting a bit, but as you know, nothing turns out exactly the same anyway. No worries, it will still be amazing, including tons of lacing and beautiful colors.

Beauty is created in all colors, and through experimenting with a variety of techniques. Never be afraid to try something new. Pour on, my friends!

Frequently Asked Questions About Strainer Pour

1. What is a twisted strainer pour?

 A twisted strainer pour involves pouring paint through a twisted or rotating strainer to create unique patterns and designs.

2. Can any strainer be used for this technique?

 While many strainers can create interesting effects, experimenting with different ones will yield varying results.

3. Is the twisted strainer pour suitable for beginners?

 Yes, it is a fun and approachable technique for artists of all levels.

4. How can I prevent the paint from mixing too much in a twisted strainer pour?

 Pouring slowly and choosing colors that blend well can help prevent overmixing.

5. Can I use a pouring medium with a twisted strainer pour?

 Yes, a pouring medium can help achieve the desired consistency and flow.

6. How long will it take for a twisted strainer pour painting to dry?

 Typically, drying time is between 24 to 72 hours, depending on the thickness of the paint and environmental conditions.

7. Can I use silicone to create cells in a twisted strainer pour?

 Absolutely, adding silicone can help in the formation of cells.